Господа, кто может подсказать, как настроить "передачу звука через PCI" под линухой
ЗЫ. в линухе я полный ламер (2 дня как установил). modprobe.conf подправил - картинка уже есть, но вот звук не получается настроить.

И небольшой оффтоп - какой программой вы радио слушаете ?

Как я настраивал 409 под ubuntu 7.04,
также работало и в 6.06 и в 6.10 (с некоторми отличиями для ядер меньше 2.6.19, там secam=d передавалось отдельно строкой в tda9887 в описанном ниже файле saa7134)
(ищите гуглем статью записки дебианщика для подробностей)

1.в /etc/modporbe.d/alsa-base
закомментировал строчку начинающуюся с install saa7134...
2.В этой же папке создал файл saa7134
с содержимым:
options saa7134 card=67 secam=d

Для ядер меньше 2.6.19 (:?:) вторая строка
tda9887 secam=d (из первой убрать).
3.Перезагрузка
4.Установка tvtime
5.Для просмотра secam каналов в настройках канала меняем с pal на secam.

Вуаля!

p.s. Совсем забыл сказать, в Debian 4.0 этот номер тоже прокатывает.

Помогите плжалуйста с настройкой TV tunera Beholder 407
Карточка вроде определяется, драйвер загружаетсся
Вывод dmesg :

Linux version 2.6.31.6-desktop-1mnb (qateam@titan.mandriva.com) (gcc version 4.4.1 (GCC) ) #1 SMP Tue Dec 8 15:43:36 EST 2009
Command line: BOOT_IMAGE=Linux_Mandriva_2010_x64 root=UUID=1760cf1e-bb22-422c-aa24-114878115ffb splash=silent vga=788
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ff90000 (usable)
BIOS-e820: 000000007ff90000 - 000000007ff9e000 (ACPI data)
BIOS-e820: 000000007ff9e000 - 000000007ffe0000 (ACPI NVS)
BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
DMI present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x7ff90 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-DFFFF uncachable
E0000-EFFFF write-through
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 disabled
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-000000007ff90000
0000000000 - 007fe00000 page 2M
007fe00000 - 007ff90000 page 4k
kernel direct mapping tables up to 7ff90000 @ 10000-14000
RAMDISK: 37971000 - 37fefb71
ACPI: RSDP 00000000000f9c00 00024 (v02 ACPIAM)
ACPI: XSDT 000000007ff90100 00044 (v01 A M I OEMXSDT 03000608 MSFT 00000097)
ACPI: FACP 000000007ff90290 000F4 (v03 A M I OEMFACP 03000608 MSFT 00000097)
ACPI: DSDT 000000007ff90400 04CBC (v01 A0279 A0279020 00000020 INTL 02002026)
ACPI: FACS 000000007ff9e000 00040
ACPI: APIC 000000007ff90390 00070 (v01 A M I OEMAPIC 03000608 MSFT 00000097)
ACPI: OEMB 000000007ff9e040 0006B (v01 A M I AMI_OEM 03000608 MSFT 00000097)
ACPI: MCFG 000000007ff950c0 0003C (v01 A M I OEMMCFG 03000608 MSFT 00000097)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at 0000000000000000-000000007ff90000
Bootmem setup node 0 0000000000000000-000000007ff90000
NODE_DATA [0000000000012000 - 0000000000016fff]
bootmap [0000000000017000 - 0000000000026ff7] pages 10
(7 early reservations) ==> bootmem [0000000000 - 007ff90000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0001000000 - 00017d84b0] TEXT DATA BSS ==> [0001000000 - 00017d84b0]
#3 [0037971000 - 0037fefb71] RAMDISK ==> [0037971000 - 0037fefb71]
#4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#5 [00017d9000 - 00017d9294] BRK ==> [00017d9000 - 00017d9294]
#6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
found SMP MP-table at [ffff8800000ff780] ff780
[ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880001c00000-ffff8800037fffff] on node 0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0007ff90
On node 0 totalpages: 524063
DMA zone: 56 pages used for memmap
DMA zone: 101 pages reserved
DMA zone: 3826 pages, LIFO batch:0
DMA32 zone: 7111 pages used for memmap
DMA32 zone: 512969 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
Allocating PCI resources starting at 80000000 (gap: 80000000:7fb80000)
NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 29 pages at ffff8800017ea000, static data 89824 bytes
Built 1 zonelists in Node order, mobility grouping on. Total pages: 516795
Policy zone: DMA32
Kernel command line: BOOT_IMAGE=Linux_Mandriva_2010_x64 root=UUID=1760cf1e-bb22-422c-aa24-114878115ffb splash=silent vga=788
PID hash table entries: 4096 (order: 12, 32768 bytes)
Initializing CPU#0
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 2052500k/2096704k available (3644k kernel code, 452k absent, 43752k reserved, 2717k data, 616k init)
SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
NR_IRQS:1280
Fast TSC calibration using PIT
Detected 2666.951 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Calibrating delay loop (skipped), value calculated using timer frequency.. 5333.90 BogoMIPS (lpj=2666951)
Security Framework initialized
TOMOYO Linux initialized
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 256
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU 0/0x0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 4 MCE banks
CPU0: Thermal monitoring enabled (TM1)
using mwait in idle threads.
Performance Counters: no PMU driver, software counters only.
ACPI: Checking initramfs for custom DSDT
ACPI: Core revision 20090521
ftrace: converting mcount calls to 0f 1f 44 00 00
ftrace: allocating 14673 entries in 58 pages
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Pentium(R) D CPU 2.66GHz stepping 07
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5333.27 BogoMIPS (lpj=2666637)
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU 1/0x1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
mce: CPU supports 4 MCE banks
CPU1: Thermal monitoring enabled (TM1)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Pentium(R) D CPU 2.66GHz stepping 07
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (10667.17 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 1 0
devtmpfs: initialized
Booting paravirtualized kernel on bare hardware
Time: 17:16:01 Date: 01/22/10
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Found Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub with MMCONFIG support.
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: Not using MMCONFIG.
PCI: Using configuration type 1 for base access
bio: create slab <bio> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI Warning: Incorrect checksum in table [OEMB] - 98, should be 88 20090521 tbutils-246
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xcbdf8000-0xcbdfbfff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0x8000-0x801f]
pci 0000:00:1d.1: reg 20 io port: [0x8400-0x841f]
pci 0000:00:1d.2: reg 20 io port: [0x8800-0x881f]
pci 0000:00:1d.3: reg 20 io port: [0x9000-0x901f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xcbdffc00-0xcbdfffff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 4700 (mask 000b)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 0007)
pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
pci 0000:00:1f.2: reg 10 io port: [0xa800-0xa807]
pci 0000:00:1f.2: reg 14 io port: [0xa400-0xa403]
pci 0000:00:1f.2: reg 18 io port: [0xa000-0xa007]
pci 0000:00:1f.2: reg 1c io port: [0x9800-0x9803]
pci 0000:00:1f.2: reg 20 io port: [0x9400-0x940f]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
pci 0000:04:00.0: reg 10 32bit mmio: [0xcf000000-0xcfffffff]
pci 0000:04:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
pci 0000:04:00.0: reg 1c 64bit mmio: [0xcc000000-0xcdffffff]
pci 0000:04:00.0: reg 24 io port: [0xe800-0xe87f]
pci 0000:04:00.0: reg 30 32bit mmio: [0xcefe0000-0xceffffff]
pci 0000:00:01.0: bridge io port: [0xe000-0xefff]
pci 0000:00:01.0: bridge 32bit mmio: [0xcc000000-0xcfffffff]
pci 0000:00:01.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:00:1c.0: bridge io port: [0xd000-0xdfff]
pci 0000:02:00.0: reg 10 32bit mmio: [0xcbfe0000-0xcbffffff]
pci 0000:02:00.0: reg 18 io port: [0xc800-0xc81f]
pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
pci 0000:00:1c.1: bridge io port: [0xc000-0xcfff]
pci 0000:00:1c.1: bridge 32bit mmio: [0xcbf00000-0xcbffffff]
pci 0000:01:0a.0: reg 10 32bit mmio: [0xcbeffc00-0xcbefffff]
pci 0000:01:0a.0: supports D1 D2
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge io port: [0xb000-0xbfff]
pci 0000:00:1e.0: bridge 32bit mmio: [0xcbe00000-0xcbefffff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 18 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
system 00:08: ioport range 0x290-0x297 has been reserved
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x800-0x87f has been reserved
system 00:09: ioport range 0x400-0x41f has been reserved
system 00:09: ioport range 0x480-0x4bf has been reserved
system 00:09: ioport range 0x900-0x90f has been reserved
system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:09: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:09: iomem range 0xfed50000-0xfed8ffff has been reserved
system 00:09: iomem range 0xffb00000-0xffbfffff could not be reserved
system 00:09: iomem range 0xfff00000-0xffffffff has been reserved
system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0f: iomem range 0xe0000000-0xefffffff has been reserved
system 00:10: iomem range 0xe0000000-0xefffffff has been reserved
system 00:11: iomem range 0x0-0x9ffff could not be reserved
system 00:11: iomem range 0xc0000-0xdffff has been reserved
system 00:11: iomem range 0xe0000-0xfffff could not be reserved
system 00:11: iomem range 0x100000-0x7fffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:04
pci 0000:00:01.0: IO window: 0xe000-0xefff
pci 0000:00:01.0: MEM window: 0xcc000000-0xcfffffff
pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.0: IO window: 0xd000-0xdfff
pci 0000:00:1c.0: MEM window: disabled
pci 0000:00:1c.0: PREFETCH window: disabled
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.1: IO window: 0xc000-0xcfff
pci 0000:00:1c.1: MEM window: 0xcbf00000-0xcbffffff
pci 0000:00:1c.1: PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1e.0: IO window: 0xb000-0xbfff
pci 0000:00:1e.0: MEM window: 0xcbe00000-0xcbefffff
pci 0000:00:1e.0: PREFETCH window: disabled
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:04: resource 0 io: [0xe000-0xefff]
pci_bus 0000:04: resource 1 mem: [0xcc000000-0xcfffffff]
pci_bus 0000:04: resource 2 pref mem [0xd0000000-0xdfffffff]
pci_bus 0000:03: resource 0 io: [0xd000-0xdfff]
pci_bus 0000:02: resource 0 io: [0xc000-0xcfff]
pci_bus 0000:02: resource 1 mem: [0xcbf00000-0xcbffffff]
pci_bus 0000:01: resource 0 io: [0xb000-0xbfff]
pci_bus 0000:01: resource 1 mem: [0xcbe00000-0xcbefffff]
pci_bus 0000:01: resource 3 io: [0x00-0xffff]
pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 6650k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1264180560.474:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 4021
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:04:00.0: Boot video device
pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: irq 25 for MSI/MSI-X
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.1: irq 26 for MSI/MSI-X
pcieport-driver 0000:00:1c.1: setting latency timer to 64
vesafb: framebuffer at 0xcd000000, mapped to 0xffffc90000900000, using 1875k, total 14336k
vesafb: mode is 800x600x16, linelength=1600, pages=2
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
Linux agpgart interface v0.103
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0e: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
PM: Resume from disk failed.
registered taskstats version 1
Magic number: 10:145:290
tty tty23: hash matches
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
rtc_cmos 00:03: setting system clock to 2010-01-22 17:16:01 UTC (1264180561)
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
Freeing unused kernel memory: 616k freed
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input2
SCSI subsystem initialized
libata version 3.00 loaded.
ata_piix 0000:00:1f.1: version 2.13
ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
ata_piix 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0xa800 ctl 0xa400 bmdma 0x9400 irq 17
ata4: SATA max UDMA/133 cmd 0xa000 ctl 0x9800 bmdma 0x9408 irq 17
ata4.01: NODEV after polling detection
ata4.00: ATAPI: Optiarc DVD RW AD-7200S, 1.06, max UDMA/100
ata4.00: configured for UDMA/100
ata1.01: ATA-7: WDC WD1600AAJB-00PVA0, 00.07H00, max UDMA/100
ata1.01: 312581808 sectors, multi 16: LBA48
ata1.01: configured for UDMA/100
scsi 0:0:1:0: Direct-Access ATA WDC WD1600AAJB-0 00.0 PQ: 0 ANSI: 5
sd 0:0:1:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
sd 0:0:1:0: [sda] Write Protect is off
sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:1:0: [sda] Attached SCSI disk
ata3.00: ATA-7: WDC WD1600AAJS-75PSA0, 05.06H05, max UDMA/133
ata3.00: 312500000 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA WDC WD1600AAJS-7 05.0 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdb] 312500000 512-byte logical blocks: (160 GB/149 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb:
scsi 3:0:0:0: CD-ROM Optiarc DVD RW AD-7200S 1.06 PQ: 0 ANSI: 5
sdb1 sdb2 <sdb5>
sd 2:0:0:0: [sdb] Attached SCSI disk
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
EXT4-fs (sdb6): barriers enabled
kjournald2 starting: pid 72, dev sdb6:8, commit interval 5 seconds
EXT4-fs (sdb6): delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs (sdb6): mounted filesystem with ordered data mode
Tomoyo security MAC extension available but disabled by default. If you want to
enable and use it, ccs-tools package must be installed.
udev: starting version 146
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
ACPI: Power Button [PWRF]
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
ACPI: Power Button [PWRB]
Floppy drive(s): fd0 is 1.44M
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
FDC 0 is a post-1991 82077
ppdev: user-space parallel port driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 20, io base 0x00008000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.31.6-desktop-1mnb uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 17, io base 0x00008400
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.31.6-desktop-1mnb uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00008800
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.31.6-desktop-1mnb uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 19, io base 0x00009000
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.31.6-desktop-1mnb uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.3
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xcbdffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: EHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.31.6-desktop-1mnb ehci_hcd
usb usb5: SerialNumber: 0000:00:1d.7
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
processor LNXCPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
processor LNXCPU:01: registered as cooling_device1
Linux video capture interface: v2.00
saa7130/34: v4l2 driver version 0.2.15 loaded
saa7134 0000:01:0a.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
saa7134[0]: found at 0000:01:0a.0, rev: 1, irq: 22, latency: 64, mmio: 0xcbeffc00
saa7134[0]: subsystem: 0000:4071, board: Beholder BeholdTV 409 FM [card=67,insmod option]
saa7134[0]: board init: gpio is c0c000
input: saa7134 IR (Beholder BeholdTV 4 as /devices/pci0000:00/0000:00:1e.0/0000:01:0a.0/input/input5
IRQ 22/saa7134[0]: IRQF_DISABLED is not guaranteed on shared IRQs
EXT4-fs (sdb6): internal journal on sdb6:8
saa7134[0]: i2c eeprom 00: 00 00 71 40 54 20 00 00 00 00 00 00 00 00 00 01
saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom f0: 42 54 56 30 32 30 32 ff ff ff ff ff ff ff ff ff

i2c-adapter i2c-0: Invalid 7-bit address 0x7a

tuner 0-0043: chip found @ 0x86 (saa7134[0])
tda9887: Unknown parameter `secam'
DVB: Unable to find symbol tda9887_attach()
All bytes are equal. It is not a TEA5767
tuner 0-0060: chip found @ 0xc0 (saa7134[0])
fuse init (API version 7.12)
tuner-simple 0-0060: creating new instance
tuner-simple 0-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
saa7134[0]: registered device video0 [v4l2]
saa7134[0]: registered device vbi0
saa7134[0]: registered device radio0
saa7134 ALSA driver for DMA sound loaded
IRQ 22/saa7134[0]: IRQF_DISABLED is not guaranteed on shared IRQs
saa7134[0]/alsa: saa7134[0] at 0xcbeffc00 irq 22 registered as card -1
p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
Adding 530104k swap on /dev/sdb7. Priority:-1 extents:1 across:530104k
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
nvidia 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:04:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 190.42 Tue Oct 20 20:25:42 PDT 2009
ondemand governor failed, too long transition latency of HW, fallback to performance governor
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
input: PC Speaker as /devices/platform/pcspkr/input/input6
iTCO_vendor_support: vendor-support=0
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=1)
intel_rng: FWH not detected
sd 0:0:1:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: Attached scsi generic sg1 type 0
sr 3:0:0:0: Attached scsi generic sg2 type 5
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
e1000e 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
e1000e 0000:02:00.0: pci_enable_pcie_error_reporting failed 0xfffffffb
e1000e 0000:02:00.0: setting latency timer to 64
e1000e 0000:02:00.0: irq 27 for MSI/MSI-X
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
HDA Intel 0000:00:1b.0: setting latency timer to 64
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input7
0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:17:31:d9:d8:b5
0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection
0000:02:00.0: eth0: MAC: 2, PHY: 2, PBA No: ffffff-0ff
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
e1000e 0000:02:00.0: irq 27 for MSI/MSI-X
e1000e 0000:02:00.0: irq 27 for MSI/MSI-X
ADDRCONF(NETDEV_UP): eth0: link is not ready
e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
0000:02:00.0: eth0: 10/100 speed: disabling TSO
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
NET: Registered protocol family 17
martian source 255.255.255.255 from 10.48.104.1, on dev eth0
ll header: ff:ff:ff:ff:ff:ff:00:1c:b0:b4:90:00:08:00
martian source 255.255.255.255 from 10.48.104.1, on dev eth0
ll header: ff:ff:ff:ff:ff:ff:00:1c:b0:b4:90:00:08:00
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk>
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
eth0: no IPv6 routers present
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ctnetlink v0.93: registering with nfnetlink.
ClusterIP Version 0.8 loaded successfully
xt_time: kernel timezone is +0300
netfilter PSD loaded - (c) astaro AG
IFWLOG: register target
Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:17:31:d9:d8:b5:00:1e:e3:88:cc:97:08:00 SRC=193.34.172.166 DST=192.168.1.2 LEN=131 TOS=0x00 PREC=0x00 TTL=120 ID=14425 PROTO=UDP SPT=61669 DPT=43123 LEN=111
Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:17:31:d9:d8:b5:00:1e:e3:88:cc:97:08:00 SRC=123.203.91.242 DST=192.168.1.2 LEN=126 TOS=0x00 PREC=0x00 TTL=113 ID=1334 PROTO=UDP SPT=18037 DPT=43123 LEN=106
Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:17:31:d9:d8:b5:00:1e:e3:88:cc:97:08:00 SRC=92.97.197.236 DST=192.168.1.2 LEN=131 TOS=0x00 PREC=0x00 TTL=114 ID=8887 PROTO=UDP SPT=22198 DPT=43123 LEN=111
Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:17:31:d9:d8:b5:00:1e:e3:88:cc:97:08:00 SRC=92.46.155.232 DST=192.168.1.2 LEN=131 TOS=0x00 PREC=0x00 TTL=114 ID=17543 PROTO=UDP SPT=16821 DPT=43123 LEN=111
Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:17:31:d9:d8:b5:00:1e:e3:88:cc:97:08:00 SRC=221.185.12.75 DST=192.168.1.2 LEN=126 TOS=0x00 PREC=0x00 TTL=107 ID=3997 PROTO=UDP SPT=16163 DPT=43123 LEN=106
Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:17:31:d9:d8:b5:00:1e:e3:88:cc:97:08:00 SRC=123.163.27.123 DST=192.168.1.2 LEN=126 TOS=0x00 PREC=0x00 TTL=111 ID=6357 PROTO=UDP SPT=26826 DPT=43123 LEN=106
Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:17:31:d9:d8:b5:00:1e:e3:88:cc:97:08:00 SRC=61.4.143.205 DST=192.168.1.2 LEN=126 TOS=0x00 PREC=0x00 TTL=107 ID=16745 PROTO=UDP SPT=7416 DPT=43123 LEN=106
Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:17:31:d9:d8:b5:00:1e:e3:88:cc:97:08:00 SRC=116.88.241.126 DST=192.168.1.2 LEN=129 TOS=0x00 PREC=0x00 TTL=116 ID=16088 PROTO=UDP SPT=8628 DPT=43123 LEN=109
Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:17:31:d9:d8:b5:00:1e:e3:88:cc:97:08:00 SRC=86.198.163.169 DST=192.168.1.2 LEN=131 TOS=0x00 PREC=0x00 TTL=113 ID=31023 PROTO=UDP SPT=44982 DPT=43123 LEN=111

в файле etc/modprobe.conf прописано следующее

устройство в dev/video0 появилось, но со знаком минус
tvtime-scanner каналы какие-то находит, но с совершенно другими частотами и ничего не показывает, всегда сплошные помехи
в ручную тоже пробовал вбивать частоты - не работает, есть только звук и только на одном канале
может быть дело в той строчке из dmesg, которую я выделит жирным и пробелами???

Ну намешали.. всего подряд.
Уберите всё, оставьте только
options saa7134 alsa=1 secam=d
Пусть ядро, достаточно свежее, само разберётся с оборудованием.

+100

Лишнее уберите, оставьте что написал WiseLord.

Плата завелась только после обновления ядра начала работать даже с теми настройками, но после того как убрал лишнее появился хороший звук, (до этого был прерывистый и с помехами), Так что огромное спасибо за совет!!!
Кстати ядро обновлял регулярно, но вот пару дней назад при очередном обновлении свершилось чудо!!!
радио проверил, все отлично работает только вот каналы почему то автоматически не находятся, что огорчает но вцелом норм